| Prefix |
Suffix |
Definition |
| . |
. |
ROLLER BRG |
| . |
. |
|
| . |
-JFT |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1000 MG/MM |
| . |
02 |
REED BEARING W/O.D. CODED TO 0.0001 INCH INCREMENTS |
| . |
03 |
REED BEARING W/O.D. CODED TO 0.00005 INCH INCREMENTS |
| . |
20 |
REED BEARING W/BORE CODED TO 0.0001 INCH INCREMENTS |
| . |
21 |
REED LUBE COBEHN INC., PRECISION INSTRUMENT OIL/MIL-L-6085 |
| . |
22 |
REED BEARING W/BORE O.D. CODED TO 0.0001 INCH INCREMENTS |
| . |
22 |
REED LUBE ANDERSON OIL CO, WINDSOR LUBE L-245X/MIL-L-6085 |
| . |
23 |
REED LUBE CODE 4264 AEROSHELL FLUID I12/MIL-L-6085A2/SKF EA |
| . |
24 |
REED LUBE E.F. HOUGHTON CO. COSMOLUBRIC 270/MIL-L-6085 |
| . |
25 |
REED LUBE STANDARD OIL OF N.J. UNIVIS P-38/MIL-L-6985- A2/SKF DA |
| . |
26 |
REED LUBE ECLIPSE PIONEER P-10/MIL-L-6085-A2/SKF EB |
| . |
27 |
REED LUBE ANDEROL L-401-D/MIL-L-6085-A2/SKF EC |
| . |
28 |
REED LUBE BRAY 885/MIL-L-6085-A2/SKF DH |
| . |
2GS |
SKF REMOVABLE MOLDED NITRILE SEAL ON BOTH SIDES |
| . |
2GSNR |
SKF SAME AS -2GS, EXCEPT WITH SNAP-RING |
| . |
2GSP |
SKF REMOVABLE MOLDED POLYACRYLIC SEAL ON BOTH SIDES |
| . |
2GSV |
SKF REMOVABLE MOLDED FLUOROCARBON SEAL ON BOTH SIDES |
| . |
2RS |
SKF SEAL OF PLATE AND SYNTHETIC RUBBER ON BOTH SIDES |
| . |
2RS2 |
VITON RUBBER SEALS FOR HIGH TEMPERATURE APPLICATIONS |
| . |
2SS |
REED TWO ARMALON SEALS |
| . |
2SS |
SKF BACK UP PLATE SEAL ON BOTH SIDES |
| . |
2Z |
REED TWO STAINLESS STEEL REMOVABLE SHIELDS |
| . |
2Z |
SKF SHIELD ON BOTH SIDES/EX 6203-2Z |
| . |
30 |
REED BEARING K/BORE CODED TO 0.00005 INCH INCREMENTS |
| . |
31 |
REED LUBE SHELL OIL, CODE 4254 AREO SHELL FL I3/MIL-L-7870 |
| . |
32 |
REED LUBE TEXAS 1692 LOW TEMP OIL/MIL-L-7870-A/SKF DD/ |
| . |
33 |
REED BEARING W/BORE O.D. CODED TO 0.00005 INCH INCREMENTS |
| . |
33 |
REED LUBE STD OIL OF N.J., ESSO AVIATION INSTRU OIL/MIL-L-7870 |
| . |
34 |
REED LUBE WINDSOR L-1018/MIL-L-7870-A/SKF DF |
| . |
35 |
REED LUBE LEHICRH CHEMICAL PROD., L-407/MIL-L-7870 |
| . |
36 |
REED LUBE GULF OIL CO., GULPHITE OIL 6/MIL-L-7870 |
| . |
41 |
REED LUBE ESSO RUST BAN 334/SKF FA/ |
| . |
42 |
REED LUBE ANDERSON OIL CO, WINDSOR RUST PREV L1384/MIL-L-644 |
| . |
43 |
REED LUBE TEXAS CO., TEXACO PRESERVATIVE OIL, SPEC/MIL-L-644 |
| . |
44 |
REED LUBE STD OIL OF N.J. , PRESERVATIVE OIL 1193/MIL-L-644 |
| . |
45 |
REED LUBE SHELL OIL CO., CODE LG-1-21 SHELL PRESERV/MIL-L-644 |
| . |
46 |
REED LUBE E. F. HOUGHTON CO., COSMOLINE 1044/MIL-L-644 |
| . |
51 |
REED LUBE VERSILUBE F-50/SKF ED |
| . |
52 |
REED LUBE DOW CORNING CORP., DC 200 FLUID/3.0 CS |
| . |
53 |
REED LUBE DC-200-20/SKF EF |
| . |
54 |
REED LUBE DC-200-30/SKF EF |
| . |
55 |
REED LUBE DC-200-350/SKF EG |
| . |
56 |
REED LUBE DC-510-20/SKF EG |
| . |
57 |
REED LUBE DC-510-50/SKF EJ |
| . |
58 |
REED LUBE DC-510-100/SKF EK |
| . |
59 |
REED LUBE DC-510-500/SKF EL |
| . |
60 |
REED LUBE VERSILUBE F-44/SKF EM |
| . |
65 |
REED LUBE TERESSTIC V-78/SKF DG |
| . |
71 |
REED LUBE STANDARD OIL OF N.J. BEACON M-325/SKF LB |
| . |
72 |
REED LUBE TEXAS CO., TEXACO 1959 UNITEMP GREASE/MIL-G-32 78 / |
| . |
73 |
REED LUBE SHELL OIL, CODE 5081 AERO SHELL GREASE LL/MIL-G-3278 |
| . |
74 |
REED LUBE E.F. HOUGHTON CO., COSMOILINE 505 GREASE/MIL-G-32 78 |
| . |
75 |
REED LUBE LEHIGH CHEM. PROD., ANDEROL L-793 GREASE/MIL-G-32 78 |
| . |
81 |
REED LUBE TEXAS 1999 HI TEMP/MIL-G-3545-B/SKF HE |
| . |
82 |
REED LUBE SHELL OIL, CODE 5076 AERO SHELL GREASE 5A/MIL-L-3545 |
| . |
83 |
REED LUBE SINCLAIR REF. CO., SINCLAIR'HI TEMP GREASE /MIL-L-3545 |
| . |
85 |
REED LUBE TEXAS 1996 UNITEMP 500/SKF HD |
| . |
86 |
REED LUBE AMER. OIL CO. SUPER MIL ASU-M-100/SKF SC/ |
| . |
87 |
REED LUBE DOW CORNING CORP. , DC 33 GREASE/MI55 LIGHT |
| . |
88 |
REED LUBE DOW CORNING CORP. , DC 55 GREASE |
| . |
89 |
REED LUBE GENERAL ELECTRIC, VERSILUBE G-300 SILICON GREASE |
| . |
90 |
REED LUBE G-300 GE VERSILUBE/SKF SF |
| . |
91 |
REED LUBE TEXACO CO., REGAL STARFAH MIL-L-7711 GREASE |
| . |
92 |
REED LUBE SHELL OIL CO., ETR GRADE 21176A GREASE |
| . |
93 |
REED LUBE TEXAS #948-1888 LO TEM/SKF CA |
| . |
94 |
REED LUBE GENERAL ELECTRIC CO., JF50 VERSILUBE SILICONE OIL |
| . |
95 |
REED LUBE SHELL ETR-B/SKF JB |
| . |
96 |
REED LUBE SHELL ETR-D/SKF JC |
| . |
97 |
REED LUBE SHELL AEROSHELL I15/MIL-G-25013-C1/SKF JA |
| . |
A |
REED 0.0000 RADIAL PLAY |
| . |
A |
SKF BEARING W/ADAPTER FOR AMERICAN SHAFT STANDARD/EX 1606-A |
| . |
A |
SKF COMPLETE PARCO-LUBRIZE OR SULITE COATING |
| . |
A |
SKF CONTACT ANGLE 30 DEGREES/EX 7205-A |
| . |
A |
SKF INTERNAL DESIGN CHANGED/EX 31308-A |
| . |
A |
TYSON DIMENSIONAL VARIATION FORM BASIC CONE OR CUP |
| . |
AB |
TYSON DIMENSIONAL VARIATION FROM BASIC FLANGED CUP |
| . |
AC |
TYSON DIMENSIONAL VARIATION FROM STANDARD CUP |
| . |
AS |
TYSON DIMENSIONAL VARIATION FORM BASIC CONE OR CUP |
| . |
AX |
TYSON DIMENSIONAL VARIATION FROM BASIC CONE OR CUP |
| . |
B |
REED 0.0001 RADIAL PLAY |
| . |
B |
SKF CONTACT ANGLE 40 DEGREES/EX 7208-B |
| . |
B |
SKF INTERNAL DESIGN CHANGED/EX 227850-B |
| . |
B |
TYSON BRASS CAGE CONE |
| . |
B |
TYSON FLANGED CUP |
| . |
BA |
SKF LUBE QUAKER CHEM. CO. FERROCOTE OIL S366-K-1 |
| . |
BA |
SKF HIGH-CAPACITY, 40-DEGREES CONTACT ?.NGLE BALL BRG/EX 7219-BA |
| . |
BB |
SKF LUBE QUAKER CHEMICAL CO. FERROCOTE OIL #346 |
| . |
BC |
SKF LUBE SHELL ENSIS OIL £30/MIL-L-21260 |
| . |
BD |
REED RADIAL PLAY, CATALOG DESIGNATION FOR TIGHT |
| . |
BD |
SKF LUBE TEXAS PRES. OIL I30/MIL-L-21260 |
| . |
BE |
SKF LUBE SOCONY MOBIL DTE 797 |
| . |
BF |
SKF LUBE QUAKER CHEMICAL CO. TMF-5815 |
| . |
BG |
SKF LUBE MOBILE KOTE $501 |
| . |
BJ |
SKF LUBE E. F. HOUGHTON CO. COSMOLINE 993/MIL-C-22235 -A |
| . |
BW |
TYSON SLOTTED FLANGED CUP |
| . |
C |
REED 0.0002 RADIAL PLAY |
| . |
C |
SKF CONTACT ANGLE 15 DEGREES/SER 7000 7200 THRU 7208-C |
| . |
C |
SKF CONTACT ANGLE 20 DEGREES/SER 7200 FORM 7209-CUP |
| . |
C |
SKF INTERNAL DESIGN CHANGED/EX 23218-C |
| . |
C |
SKF SPHERICAL ROLLER BRG W/GUIDE RING PRESSED TYPE CAGE |
| . |
C |
TYSON SPECIAL HIGH-CAPACITY SERIES CONE |
| . |
C02 |
SKF EXTRA CLOSE INNER RING RUNNING ACCURACY STD INTERNAL CLEAR |
| . |
C03 |
SKF CLOSE OUTER RING RUNNING ACCURACY STD INTERNAL CLEAR |
| . |
C04 |
SKF EXTRA CLOSE OUTER RING RUNNING ACCURACY SDT INTERNAL CLEAR |
| . |
C06 |
SKF COMBINATION OF C02 PLUS C03 |
| . |
C07 |
SKF COMBINATION OF C01 PLUS C04 |
| . |
C2 |
SKF RADIAL CLEARANCE LESS THAN NORMAL |
| . |
C20 |
SKF REDUCED I.D. TOLERANCE APPROACHING NOMINAL DIMENSION |
| . |
C3 |
SKF RADIAL CLEARANCE GREATER THAN NORMAL |
| . |
C30 |
SKF REDUCED I.D. TOLERANCE APPROACHING LOW LIMIT |
| . |
C4 |
SKF RADIAL CLEARANCE GREATER THAN C3 |
| . |
C40 |
SKF REDUCED O.D. TOLERANCE APPROACHING NOMINAL DIMENSION |
| . |
C481 |
SKF SUPER PRECISION EQUIV TO RBEC-5 IN BEARINGS/ TAPER BORE/CL FIT |
| . |
C4817 |
SKF EQUIV TO RBEC-5 TOL, CL FIT, C7 EXTRA-SMOOTH RUNNING |
| . |
C5 |
SKF RADIAL CLEARANCE GREATER THAN C4 |
| . |
C50 |
SKF REDUCED O.D. TOLERANCE APPROACHING LOW LIMIT |
| . |
C60 |
SKF COMBINATION OF C20 PLUS C50 |
| . |
C7 |
SKF PRECISION ROLLER TOLERANCE |
| . |
C70 |
SKF COMBINATION OF C20 PLUS C40 |
| . |
C77 |
SKF SUPER PRECISION ROLLER TOLERANCE |
| . |
C78 |
SKF SUPER PRECIS, ABEC-5 STD INTERNAL CLEARANCE |
| . |
C8 |
SKF SPECS ON EXECUTION INSPECTION APPLY/AIRCRAFT/ |
| . |
C99177 |
SKF SUPER PRECISION, ABEC-7 TOL, CL FIT C77 EXTRA-SMOOTH RUNNING |
| . |
C997 |
SKF SUPER-PRECISION, ABEC-7 TOLER C7 EXTRA-SMOOTH RUNNING |
| . |
CA |
SKF LUBE TEXAS 984-1888 LO TEMP |
| . |
CA |
SKF SPHERICAL ROLLER BEARING W/SEPARATE GUIDE RING INTEGRAL SIDE |
| . |
CAM |
SKF SPHERICAL ROLLER BEARING W/MACHINED BRONZE INNER PILOTED CAGE |
| . |
CAM2 |
SKF SPHERICAL ROLLER BEARING W/MACHINED BRONZE ROLLER RIDING CAGE |
| . |
CF |
REED RADIAL PLAY, CATALOG DESIGNATION FOR STANDARD |
| . |
CIO |
SKF I.D. O.D. WITHIN LIMITS OF MEAN DIAMETER |
| . |
CJ |
SKF SPHERICAL ROLLER BEARING PRESSED STEEL INNER PILOTED CAGE |
| . |
CK30. |
SKF C-TYPE SPHERICAL BEARING WITH L-TO-30 TAPERED BORE/GERMANY |
| . |
CL |
SKF RADIAL CLEARANCE LESS THAN C2 |
| . |
CL3 |
SKF BORE, O.D. ECCENTRICITY TOLERANCES EQUIV TO ABEC-3 |
| . |
CO1 |
SKF CLOSE INNER RING RUNNING ACCURACY STD INTERNAL CLEAR |
| . |
COS |
SKF CLOSE RUNNING ACCURACY OF BOTH INNER OUTER RINGS |
| . |
COS |
SKF EXTRA CLOSE RUNNING ACCURACY OF BOTH INNER OUTER RINGS |
| . |
CP |
TYSON CHROME PLATED CUP OR CONE |
| . |
CSV |
SKF REMOVABLE MOLDED FLUOROCARBON SEAL |
| . |
CY |
SKF PRESS BRASS, WINDOW TYPE CAGE, I.R. CENTERED, FOR C SPHERICAL |
| . |
D |
REED 0.0003 RADIAL PLAY |
| . |
D |
REED WOUND-SPRING TYPE RETAINER |
| . |
D |
SKF MATCHED BOXED IN PAIRS FOR DUPLEX MOUNTING |
| . |
D |
TYSON DOUBLE CONE OR CUP |
| . |
D. .B |
REED BACK-TO-BACK MOUNT, PRELOAD LISTED IN POUNDS BETWEEN LETTERS |
| . |
D. .F |
REED FACE-TO-FACE MOUNT, PRELOAD LISTED IN POUNDS BETWEEN LETTERS |
| . |
D..T |
REED TANDEM MOUNTING, PRELOAD LISTED IN POUNDS BETWEEN LETTERS |
| . |
D..U |
REED UNIV DUPLEX MOUNT, PRELOAD LISTED IN POUNDS BETWEEN LETTERS |
| . |
D9 |
SKF DG BALL BEARING W/GROOVES FOR SEALS SHIELDS BUT W/OUT SAME |
| . |
DA |
SKF LUBE STANDARD OIL OF N.J. UNIVIS P-38/MIL-L-6085-A2/ |
| . |
DA |
TYSON DIMENSIONAL VARIATION OF BASIC DOUBLE CONE |
| . |
DA |
TYSON DOUBLE CUP WITH SPHERICAL O.D. |
| . |
DB |
SKF LUBE ESSO TURBO OIL 4040/MIL-L-7808-E/ |
| . |
DB |
TYSON FLANGED DOUBLE CUP |
| . |
DC |
SKF LUBE ESSO AVIATION INSTRUMENT OIL/MIL-L-7870 |
| . |
DD |
SKF LUBE TEXAS 1692 LOW TEMP OIL/MIL-L-7870 |
| . |
DD |
TYSON LONG DOUBLE CONE OR DOUBLE CUP |
| . |
DE |
SKF LUBE WINDSOR LUBE L245X/MIL-L-6085-A2 |
| . |
DE |
TYSON DIMENSIONAL VARIATION OF BASIC DOUBLE CONE |
| . |
DF |
SKF LUBE WINDSOR LUBE L-1018/MIL-L-7870A |
| . |
DG |
SKF LUBE TERESSTIC V-78 |
| . |
DH |
SKF LUBE BRAY 885/MIL-L-6085-A2 |
| . |
DJ |
SKF LUBE TERESSTIC V-79 |
| . |
DK |
SKF LUBE ALASKAN OIL 143 |
| . |
DO |
SKF SEPARABLE BEARING, NON-INTERCHANGEABLE MAIN COMPONENTS |
| . |
DS |
TYSON DIMENSIONAL VARIATION OF BASIC DOUBLE CUP |
| . |
DT |
TYSON DOUBLE CUP, TAPERED O.D. |
| . |
DW |
TYSON DOUBLE CONE OR CUP WITH KEYWAY OR SLOT |
| . |
E |
REED 0.0004 RADIAL PLAY |
| . |
E3 |
REED CORRESPONDS TO ABEC-3 PRECISION |
| . |
E4 |
SKF SEMI-PRECISION LINEAR MOTION ASSEMBLY |
| . |
E5 |
REED CORRESPONDS TO ABEC-5 PRECISION |
| . |
E7 |
REED CORRESPONDS TO ABEC-7 PRECISION |
| . |
EA |
SKF LUBE CODE 4264 AERO SHELL FLUID J12/MIL-L-6085-A2 |
| . |
EA |
TYSON CUP SPACER |
| . |
EB |
SKF LUBE ECLIPSE PIONEER P-10/MIL-L-6085-A2 |
| . |
EB |
TYSON CUP SPACER |
| . |
EC |
SKF LUBE ANDEROL L-401-D/MIL-L-6085-A2 |
| . |
EC |
TYSON CUP SPACER |
| . |
ED |
SKF LUBE VERSILUBE F-50 |
| . |
ED |
TYSON CUP SPACER |
| . |
ED |
TYSON SHORT DOUBLE CUP |
| . |
EE |
SKF LUBE DC200-20 |
| . |
EF |
SKF |
| . |
EG |
SKF |
| . |
EH |
SKF LUBE DC510-20 |
| . |
EJ |
SKF LUBE DC510-50 |
| . |
EK |
SKF LUBE DC510-100 |
| . |
EL |
SKF LUBE DC510-500 |
| . |
EM |
SKF LUBE VERSILUBE F-44 |
| . |
EN |
SKF LUBE 6 TO 8 PARTS XYLENE PLUS 1 PART DC510-50/EJ/ |
| . |
EO |
SKF EXTRA PRECISION LINEAR MOTION ASSEMBLY |
| . |
F |
REED 0.0005 RADIAL PLAY |
| . |
F |
SKF MACHINED STEEL OR MONEL CAGE |
| . |
F3 |
SKF MACHINED DUCTILE IRON CAGE |
| . |
FA |
SKF. LUBE ESSO RUST BAN 334 |
| . |
FB |
SKF LUBE WILSON BROWER THIXOTROPIC OIL 832-20 |
| . |
FC |
SKF LUBE STANDARD OF N.J. ESSO TURBO 16/MIL-C-8188C |
| . |
FC |
SKF MACHINED STEEL OR MONEL CAGE CENTERED IN I. R. /PHILA |
| . |
FN |
REED RADIAL PLAY, CATALOG DESIGNATION FOR LOOSE |
| . |
FP |
SKF STEEL OR SPECIAL CAST IRON CAGE, SLOT OR BROACH ROLLER CENT |
| . |
FPC |
SKF SAME AS -FP, EXCEPT INNER RING CENTERED |
| . |
FPS |
SKF SAME AS -FB, EXCEPT OUTER RING CENTERED |
| . |
FR |
TYSON FULL ROLL TYPE CONE |
| . |
FS |
SKF MACHINED STEEL OR MONEL CAGE CENTERED IN O.R./PHILA |
| . |
G |
REED 0.0006 RADIAL PLAY |
| . |
G |
SKF FLUSH-GROUND SIDE SURFACES FOR DUPLEX MOUNTING |
| . |
G02 |
SKF 20 POUNDS PRELOAD |
| . |
G05 |
SKF 50 POUNDS PRELOAD |
| . |
G5 |
SKF 500 POUNDS PRELOAD |
| . |
GA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 800 MG/MM |
| . |
GA |
SKF LUBE WILSON BROWER 300-1 |
| . |
GB |
SKF LUBE WILSON BROWER 300-1-C |
| . |
GC |
SKF LUBE VALVOLINE OIL CO. TECTYL *437/MIL-C-11796B |
| . |
GD |
SKF LUBE GULF PETROLATUM EXTRA AMBER |
| . |
GL |
SKF 100 POUNDS PRELOAD |
| . |
GM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 800 MG/MM |
| . |
GP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 800 MG/MM |
| . |
GS |
SKF REMOVABLE MOLDED NITRILE SEAL ON ONE SIDE |
| . |
GSNBR |
SKF SAME AS -GSNB , EXCEPT WITH SNAP-RING |
| . |
GSNR |
SKF SAME AS -GSN, EXCEPT WITH SNAP-RING |
| . |
GSP |
SKF REMOVABLE MOLDED POLYACRYLIC SEAL |
| . |
GSZ |
SKF GS-SEAL ON ONE SIDE, Z-PLATE ON THE OTHER SIDE |
| . |
H |
REED 0.0007 RADIAL PLAY |
| . |
H |
SKF PRESSED HARDENED STEEL SNAP CAGE |
| . |
HA |
SKF TORQUE TEST, AVERAGE TORQUE VALUE OF 900 MG/MM |
| . |
HA |
SKF LUBE STANDARD OF N.J. ANDOK C |
| . |
HB |
SKF LUBE STANDARD OF N.J. ANDOK-260 |
| . |
HC |
REED CROWN TYPE STAINLESS STEEL RETAINER |
| . |
HC |
SKF LUBE STANDARD OF CALIF. KPM AVIATION 42/MIL-G-3545B |
| . |
HC |
SKF PRESSED STEEL SNAP CAGE, INNER RING CENTERED |
| . |
HD |
SKF LUBE TEXAS 1996 UNITEMP 500 |
| . |
HE |
SKF LUBE TEXAS 1999 HI-TEMP/MIL-G-3545-B |
| . |
HF |
SKF LUBE STANDARD OF CALIF. CHEVRON OHT/MIL-G-18709-A3 |
| . |
HG |
SKF LUBE STANDARD OF INDIANA RYKON $2 |
| . |
HH |
SKF LUBE IMPERIAL OIL CO. OF CANADA ESSO MP GREASE 7 |
| . |
HJ |
SKF LUBE SHELL AERO SHELL I5/MIL-G-3545B |
| . |
HK |
SKF LUBE N.Y. N.J. S-59 |
| . |
HL |
SKF LUBE ROYCO 5-N/MIL-G-3545-B/ |
| . |
, HM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 900 MG/MM |
| . |
HM |
SKF LUBE TEXACO TG 7016 |
| . |
HP |
REED TORQUE TEST, 'PEAK TORQUE VALUE OF 900 MG/MM |
| . |
J |
REED 0.0008 RADIAL PLAY |
| . |
J |
REED RIBBON TYPE STAINLESS STEEL RETAINER |
| . |
J |
SKF PRESSED UN-HARDENED STEEL CAGE |
| . |
JA |
=C4054SKF LUBE SHELL AEROSHELL S15/MIL-G-25013-C1 |
| . |
JB |
SKF LUBE SHELL ETR-B |
| . |
JC |
SKF LUBE SHELL ETR-D |
| . |
JM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 1000 MG/MM |
| . |
JP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 1000 MG/MM |
| . |
K |
REED 0.0009 RADIAL PLAY |
| . |
K |
SKF BEARING WITH L-TO-12 TAPERED BORE/EX 1207-K |
| . |
K30 |
SKF BEARING WITH L-TO-30 TAPERED BORE/EX 24140-CK30 |
| . |
KA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1100 MG/MM |
| . |
KM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 1100 MG/MM |
| . |
KP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 1100 MG/MM |
| . |
L |
REED 0.0010 RADIAL PLAY |
| . |
L |
SKF MACHINED DURAL CAGE |
| . |
LA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1200 MG/MM |
| . |
LA |
SKF LUBE TEXAS LOW-TEMP EP *1346/MIL-G-13827B |
| . |
LB |
SKF LUBE STD OF N.J. BEACON M-325/MIL-G-32 78 |
| . |
LC |
SKF LUBE MID CONTINENT OIL CO. MIDCO 287 INSTRUMENT GREASE |
| . |
LC |
SKF MACHINED DURAL CAGE, CENTERED IN INNER RING |
| . |
LD |
SKF LUBE SHELL AEROSHELL *7A/MIL-G-3278-AL |
| . |
LE |
SKF LUBE ANDEROL L-793 |
| . |
LF |
SKF LUBE ANDEROL L-730/MIL-L-19701 |
| . |
LG |
SKF LUBE ANDEROL L-795 |
| . |
LH |
SKF LUBE SHELL AEROSHELL 7/MIL-G-2 3827-A1 |
| . |
LJ |
SKF LUBE MOBILE GREASE 12 8/MIL-G-23827-A1 |
| . |
LK |
SKF LUBE ROYCO GREASE T27/MIL-G-23827-AL |
| . |
LL |
SKF LUBE AMERIC OIL CO. SUPERMIL ASU-72832/MIL-G-23827-A1 |
| . |
LM |
REED TORQUE TEST, MODAL VALUE OF 1200 MG/MM |
| . |
LP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 1200 MG/MM |
| . |
LP |
SKF MACHINED DURAL CAGE W/BROACHED POCKETS |
| . |
LPC |
SKF MACHINED DURAL CAGE W/BROACHED POCKETS, I.R. CENTERED |
| . |
LPS |
SKF MACHINED DURAL CAGE W/BROACHED POCKETS, O.R. CENTERED |
| . |
LW1 |
TYSON CONE WITH ONE SPECIAL KEYWAY |
| . |
M |
REED 0.0011 RADIAL PLAY |
| . |
M |
SKF MACHINED BRONZE CAGE |
| . |
M2 |
SKF SPHERICAL ROLLER BEARING W/ ROLLER-RIDING CAGE AND NO GUIDE-RING |
| . |
M2 |
SKF TRACTION MTR BEARING W/ SOLID BRASS DRILL CAGE, ROLL-CENTERED |
| . |
M5 |
SKF SOLID SILIC-IRON BRONZE CAGE/ALL VARIATIONS OF M APPLY |
| . |
MA |
SKF LUBE MASTER LUBRICANT M-31 |
| . |
MB |
SKF LUBE N.Y. N.J. W-56/MIL-G-18709-A3 |
| . |
MC |
SKF LUBE SOCONY VACUUM BRB LIFETIME |
| . |
MC |
SKF MACHINED BRONZE CAGE CENTERED IN INNER RACE |
| . |
MC5 |
SKF CAGE-SAME AS MC, EXC SILICONE IRON BRONZE MATERIAL |
| . |
MD |
SKF LUBE SHELL CYPRINA *3 |
| . |
MG |
SKF LUBE SHELL ALVANIA B/AAR SPEC. M-917-56 |
| . |
MH |
SKF LUBE FISKE BROS. LUBRIPLATE 107 |
| . |
MJ |
SKF LUBE SHELL ALVANIA 13 |
| . |
MK |
SKF . LUBE SHELL DARINA F2 |
| . |
MN |
SKF - LUBE SHELL DARINA AX |
| . |
MO |
SKF LUBE TEX 1909 JOURNL RB GREASE H/AAR SPEC. M-917-63 GRADE B |
| . |
MP |
SKF MACHINED BRONZE CAGE WITH BROACHED POCKETS |
| . |
MPC |
SKF CAGE-SAME AS -MP EXCEPT CENTERED IN INNER RACE |
| . |
MPC5 |
SKF CAGE-SAME AS -MPC, EXCEPT SILICONE IRON BRONZE MATERIAL |
| . |
MPS |
SKF CAGE-SAME AS -MP EXCEPT CENTERED IN THE OUTER RACE |
| . |
MPS5 |
SKF CAGE-SAME AS -MPS, EXC SILICON IRON BRONZE MATERIAL |
| . |
MR |
SKF LUBE TEXACO 2301 RB GREASE/AAR SPEC M-917-63 GRADE A |
| . |
MS |
SKF LUBE ESSO ARAPEN RB-350/AAR SPEC. M-917-63 GRADE A |
| . |
MS |
SKF MACHINED BRONZE CAGE CENTERED IN THE OUTER RACE |
| . |
MS5 |
SKF CAGE-SAME AS -MS, EXCEPT SILICON IRON BRONZE MATERIAL |
| . |
MT |
SKF LUBE RICHFIELD ROCOLUBE/AAR SPEC M-917-63 GRADE A |
| . |
MU |
SKF LUBE SHELL ALVANIA C/AAR SPEC M-917-63 GRADE B |
| . |
MW |
SKF LUBE MOBIL PLEX EP-2/MIL-G-18709-A3 |
| . |
MX |
SKF LUBE NON-FLUID OIL CO. F-924-AF |
| . |
MY |
SKF LUBE UNION OIL OF CALIFORNIA UNOBA $1 |
| . |
N |
REED 0.0012 RADIAL PLAY |
| . |
N |
SKF GROOVE IN OUTER RACE BUT WITHOUT SNAP-RING/EX 6205-N |
| . |
N |
TYSON' TYSON SERIES ONLY |
| . |
NA |
REED TORQUE TEST, AVERAGE VALUE OF 1300 MG/MM |
| . |
NA |
SKF LUBE SHELL B B/MIL-G-10924B |
| . |
NB |
SKF. LUBE AEROSHELL F 14/MIL-G-25537-A1 |
| . |
NFR |
TYSON FULL-ROLL CONE IN TYSON SERIES |
| . |
NM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 1300 MG/INM |
| . |
NP |
REED TORQUE TEST, PEAK VALUE OF 1300 MG/MRA |
| . |
NR |
SKF SNAP RING ON OUTER RING |
| . |
NW |
TYSON SLOTTED FRONT FACE ON NA-TYPE CONE |
| . |
NW2 |
TYSON CONE WITH 2 SPECIAL WOODRUFF KEYS |
| . |
NW4 |
TYSON CONE WITH 1 KEYWAY EXTENDED THROUGH CONE BORE |
| . |
Q |
SKF QUIET RUNNING BEARING |
| . |
QA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1400 MG/MM |
| . |
QM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 1400 MG/MM |
| . |
QP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 1400 MG/MM |
| . |
RA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1500 MG/MRA |
| . |
RA |
SKF LUBE DOW CORNING DC-33/LIGHT |
| . |
RB |
SKF LUBE DOW CORNING DC-44/LIGHT/MIL-L-15719-A3 |
| . |
RB |
TYSON CUP WITH SNAP RING |
| . |
RD |
SKF LUBE DOW CORNING DC6 SILICONE |
| . |
RL |
SKF FOLLOWED BY NON-SIGNIFICANT NOS/SPEC INTERN RAD CLEAR |
| . |
RM |
REED TORQUE. TEST, MODAL TORQUE VALUE OF 1500 MG/MM |
| . |
RP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 1500 MG/MM |
| . |
RS |
SKF SEAL OF PLATE AND SYNTHETIC RUBBER ON ONE SIDE |
| . |
RSNBR |
SKF SAME AS-RSNB, EXCEPT WITH SNAP-RING |
| . |
RSNR |
SKF SAME AS-RSN, EXCEPT WITH SNAP-RING |
| . |
RSZ |
SKF RS-SEAL ON ONE SIDE, Z -PLATE ON THE OTHER SIDE |
| . |
S |
SKF DIMENSIONAL VARIATION FROM BASIC CONE |
| . |
SA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1600 MG/MM |
| . |
SA |
SKF LUBE KEYSTONE M-89 SILICONE |
| . |
SB |
SKF LUBE DOW CORNING DC-4 SILICONE |
| . |
SC |
SKF LUBE AMERICAN OIL CO. SUPERMIL ASU-M-100 |
| . |
SD |
SKF LUBE AMERICAN OIL CO. SUPERMIL ASU-M-40 |
| . |
SE |
SKF LUBE DOW CORNING PNEUMATIC GREASE 55-M/MIL-L-4 343 |
| . |
SF |
SKF LUBE G-300 GE VERSILUBE |
| . |
SG |
SKF LUBE AMERICAN OIL CO. SUPERMIL M-125 |
| . |
SH |
SKF LUBE MOBIL GREASE 24 |
| . |
SJ |
SKF LUBE AMERICAN OIL CO. SUPERMIL ASU-31052/MIL-G-25013D |
| . |
SK |
SKF LUBE MOBIL TEMP FL |
| . |
SM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 1600 MG/RAM |
| . |
SP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 1600 MG/MM |
| . |
SS |
REED ONE ARMALON SEAL |
| . |
SS |
SKF BACK-UP PLATE SEAL ON ONE SIDE |
| . |
SW |
TYSON DIMENSIONAL VARIATION FROM BASIC CONE WITH KEYWAY |
| . |
SW |
TYSON NA-TYPE CONE WITH SLOTTED FRONT-FACE |
| . |
SWE |
TYSON NA-CONE, SLOT FRONT-FACE EXTENDED FACE-FACE GROUND FOR SEAL |
| . |
T |
REED SYNTHETIC SNAP-ON TYPE RETAINER |
| . |
T |
SKF PHENOLIC CAGE/EX 6305-T |
| . |
T |
TYSON CUP WITH TAPERED O.D. |
| . |
T |
TYSON TAPERED BORE ON CONE |
| . |
TA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1700 MG/MM |
| . |
TA |
SKF LUBE STANDARD OF N.J. ANDOK B/MIL-G018709-A3 |
| . |
TB |
SKF LUBE TEXACO 1982 REGAL STARFAK F3 |
| . |
TC |
REED SYNTHETIC INNER RING SUPPORTED RETAINER |
| . |
TC |
SKF LUBE STANDARD OF N.J. ESSO AVIATION GENERAL PURPOSE |
| . |
TC |
SKF PHENOLIC CAGE, INNER RING CENTERED/EX 6204-TC |
| . |
TD |
SKF LUBE SOCONY MOBILGREASE AERO GENERAL PURPOSE |
| . |
TD |
TYSON DOUBLE CONE WITH TAPERED BORE |
| . |
TE |
SKF LUBE SHELL ALVANIA J2/MIL-G-18709-A3 |
| . |
TF |
SKF LUBE NEW YORK NEW JERSEY S-58/MIL-G-18709-A3 |
| . |
TG |
SKF LUBE MASTER LUBRICANT LUBRICO M-24-M/MIL-G-18709-A3 |
| . |
TH |
SKF LUBE SHELL CYPRINA RA |
| . |
TJ |
SKF LUBE STANDARD OIL OF N.J. ANDOK BR |
| . |
TK |
SKF LUBE IMPERIAL OIL CO ./CANADA/ANDOK 280 |
| . |
TL |
SKF LUBE IMPERIAL OIL CO ./CANADA/ESSO MP GREASE M |
| . |
TM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 1700 MG/MM |
| . |
TM |
SKF LUBE TEXAS REGAL AFB #2/MIL-G-7711A |
| . |
TN |
SKF LUBE KEYSTONE 84-HX LIGHT |
| . |
TN |
SKF NYLON OR NYLAFIL CAGE/EX 6203-TN |
| . |
TNC |
SKF NYLON OR NYLAFIL CAGE, INNER RING CENTERED/EC 6205-TNC |
| . |
TNS |
SKF NYLON OR NYLAFIL CAGE, OUTER RING CENTERED/EX 6205-TNS |
| . |
TO |
SKF LUBE SHELL ALVANIA EP2 |
| . |
TP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 1700 MG/MM |
| . |
TP |
SKF LUBE CHEVRON OIL CO. RPM AVIATION GREASE TL |
| . |
TS |
REED SYNTHETIC OUTER RING SUPPORTED RETAINER |
| . |
TS |
SKF PHENOLIC CAGE, OUTER RING CENTERED/EX 6204-TS |
| . |
U |
SKF ALIGNING WASHER FOR THRUST BALL BEARING/EX 708-U/PHILA |
| . |
UA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1800 MG/MM |
| . |
UA |
SKF LUBE AM. OIL CO. SUPERMIL ASU 06752/MIL-G-27560-A3 |
| . |
UB |
SKF LUBE CHEVRON OIL CO. BRB-2 |
| . |
UC |
SKF LUBE SHELL AEROSHELL F 16/MIL-G-25760 |
| . |
UD |
SKF LUBE MOBIL GREASE S38/MIL-G-81322A |
| . |
UE |
SKF LUBE CHEVRON OIL CO. SRI 12 |
| . |
UM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 1800 MG/MM |
| . |
UP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 1800 MG/MM |
| . |
VAA |
SKF SPECIAL CHARACTERISTICS IN BASIC SIZE-LETTERS INSIGNIFICANT |
| . |
VAB |
SKF SPECIAL CHARACTERISTICS IN BASIC SIZE-LETTERS INSIGNIFICANT |
| . |
VAC |
SKF SPECIAL CHARACTERISTICS IN BASIC SIZE-LETTERS INSIGNIFICANT |
| . |
VSA |
SKF SPECIAL CHARACTERISTICS IN BEARING SERIES-LETTERS INSIGNIFICANT |
| . |
VSB |
SKF SPECIAL CHARACTERISTICS IN BEARING SERIES-LETTERS INSIGNIFICANT |
| . |
VSC |
SKF SPECIAL CHARACTERISTICS IN BEARING SERIES-LETTERS INSIGNIFICANT |
| . |
W |
REED FULL BALL COMPLEMENT DESIGN -NO RETAINER |
| . |
W |
TYSON 2 ANG SLOTS DIAMETRICALLY OPPOSITE IN CONE BACK-FACE |
| . |
W10 |
SKF BEARING WITH DULITED SURFACES |
| . |
W100 |
REED 1200 NIG/MM MAX STARTING TORQUE, 75 GR. LOAD |
| . |
W101 |
REED 1000 MG/MM MAX STARTING TORQUE, 75 GR . LOAD |
| . |
W102 |
REED 5400 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . |
W103 |
REED 5000 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . |
W104 |
REED 4600 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . |
W105 |
REED 4200 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . |
W106 |
REED 3800 MG/MM MAX STARTING TORQUE, 400 GR. LOAD |
| . |
W107 |
REED 3400 MG/MM MAX STARTING TORQUE, 400 GR . LOAD |
| . |
W108 |
SKF NON-STANDARD SHIELD CLEARANCE OF 0.008 TO 0.009 INCH |
| . |
W109 |
REED EXTREME CORROSION RESISTANCE |
| . |
W115 |
SKF WLL BEARINGS WITH ADDITION OF W5 FEATURES |
| . |
W12 |
SKF RACEWAYS AND ROLLING ELEMENTS DULITED. ALL OTHER SURFACES PARCO-LUBRIZED |
| . |
W125 |
SKF W12 BEARINGS WITH ADDITION OF W5 FEATURES |
| . |
W13 |
SKF BEARING WITH PARCO-LUBRIZED BORE AND O.D. |
| . |
W14 |
SKF DULITED RINGS ROLLING ELEMENTS, PARCO-LUBRIZED BORE O.D. |
| . |
W15 |
SKF ALL SUFACES DULITED, EXCEPT LANDS SUPPORTING CAGE RIDE |
| . |
W16 |
SKF PARCO-LUBRIZED INNER RING AND O.D. OF OUTER RING |
| . |
W17 |
SKF DULITED CAPPED BEARING, EXCEPT SHIELD OR SEAL TIN-COATED |
| . |
W18 |
SKF BEARING W/SPECIFIC DULITED SURFACE OR SURFACES |
| . |
W19 |
SKF BEARINGS WITH SPECIAL RADIAL LOOSENESS LIMITS |
| . |
W2 |
SKF BEARING MEETING SPECIAL TORQUE REQUIREMENTS |
| . |
W21 |
SKF FLUSH GROUND BEARING W/INNER OUTER RINGS OF EQUAL WIDTH/ CLOSE CROSS CORNER TOLERANCES./ |
| . |
W215 |
SKF W21 BEARINGS WITH ADDITION OF W5 FEATURES |
| . |
W216 |
SKF W21 BEARINGS WITH ADDITION OF W6 FEATURES |
| . |
W22 |
SKF SPEC REDUCED O.D. TOLERANCE FOR O.R. -STD TOLER FOR I.R. |
| . |
W23 |
SKF SPECIAL FEATURES FOR TRACTION MOTOR BEARINGS |
| . |
W24 |
SKF SPECIAL TOLERANCE FOR SEAL OR SHIELD LOCATION ON CAPPED BEARINGS |
| . |
W25 |
SKF SPHERICAL ROLLER BEARINGS W/CLOSE OUTER RING WIDTH TOLERANCE |
| . |
W26 |
SKF SPHERICAL ROLLER BEARINGS W/HOLES DRILLED THROUGH THE INNER RING |
| . |
W27 |
SKF SY PILLOW BLOCK BEARINGS WITH A SPECIAL COLLAR |
| . |
W29 |
SKF CYLINDRICAL W/SPECIAL RADIAL LOOSENESS INTERCHANGEABILITY |
| . |
W2CX |
SKF OIL HOLES IN OUTER 'RING OF SPHERICAL ROLLER BEARING |
| . |
W3 |
SKF BEARING MARKED TO SHOW MEASURED ACCURACY |
| . |
W30 |
SKF BEARINGS WITH SPECIFIED PARTS TIN-PLATED |
| . |
W31 |
SKF SPHER BEARXNGS INSPECTED TO CERTAIN QUALITY CONTROL REQUIREMENT |
| . |
W32 |
SKF PLATES SEALS INSPECTED TO SPECIAL MINIMUM LOOSENESS |
| . |
W33 |
SKF SPHERICAL ROLLER BEARING W/OIL HOLES CIRCUMFERENTIAL GROOVE IN O.D. |
| . |
W34 |
SKF CAGE HAS BEEN 10 PERCENT FLUORESCENT PENETRANT INSPECTED |
| . |
W35 |
SKF SPDG BEARING W/ REDUCED SIDE RUN-OUT OF INNER RING |
| . |
W36 |
SKF BEARINGS THAT HAVE BEEN QUALITY AUDITED FOR BORE AND O.D. |
| . |
W37 |
SKF SPECIAL AIRCRAFT BEARING IDENTIFICATION |
| . |
W38 |
SKF WRIGHT AERO, QUALITY ASSURANCE |
| . |
W39 |
SKF ALLISON QUALITY ASSURANCE |
| . |
W4 |
SKF HI-POINT OF ECCENTRICITY MARKED ON INNER RING OR SLEEVE |
| . |
W40 |
SKF BEARINGS WITH SILVER PLATED CAGE |
| . |
W405 |
SKF W40 BEARINGS WITH ADDITION OF W5 FEATURES |
| . |
W41 |
SKF BEARINGS WITH SILVER AND LEAD PLATED CAGES |
| . |
W42 |
SKF BEARINGS WITH SILVER AND LEAD-INDIUM PLATED CAGE |
| . |
W43 |
SKF BEARINGS WITH CHROME PLATED CAGE |
| . |
W45 |
SKF CADMIUM PLATED LOCKOUTS AND WASHERS |
| . |
W5 |
SKF CUSTOMERS PART NUMBER MARKED ON BEARING |
| . |
W50 |
SKF BEARINGS W/DOUBLE STABILIZED HEAT TREATED INNER RACES |
| . |
W501 |
SKF W19 BEARINGS WITH ADDITION OF W36 FEATURES |
| . |
W502 |
SKF W22 BEARINGS WITH ADDITION OF W33 FEATURES |
| . |
W503 |
SKF W4 BEARINGS WITH ADDITION OF W33 FEATURES |
| . |
W504 |
SKF W55 BEARINGS WITH ADDITION OF W33 FEATURES |
| . |
W505 |
SKF W51 BEARINGS WITH ADDITION OF W33 FEATURES |
| . |
W506 |
SKF W31 BEARINGS WITH ADDITION OF W33 FEATURES |
| . |
W507 |
SKF W4 BEARINGS WITH ADDITION OF W31 FEATURES |
| . |
W508 |
SKF W4 BEARINGS WITH ADDITION OF W31 FEATURES |
| . |
W509 |
SKF W26 BEARINGS WITH ADDITION OF W31 AND W33 FEATURES |
| . |
W51 |
SKF SPECIAL NOISE TEST AND CARTON MARKING |
| . |
W510 |
SKF W33 BEARINGS WITH ADDITION OF K56 FEATURES |
| . |
W512 |
SKF W22 BEARINGS WITH ADDITION OF W31 AND W33 FEATURES |
| . |
W513 |
SKF W33 BEARINGS WITH ADDITION OF W26 FEATURES |
| . |
W514 |
SKF W26 BEARINGS WITH ADDITION OF W31 FEATURES |
| . |
W515 |
SKF W4 BEARINGS WITH ADDITION OF W58 FEATURES |
| . |
W516 |
SKF W10 BEARINGS WITH ADDITION OF W33 FEATURES |
| . |
W517 |
SKF COMBINATION OF W33 PLUS W61 |
| . |
W518 |
SKF COMBINATION OF W20 PLUS W26 |
| . |
W519 |
SKF COMBINATION W81 PLUS W20/USED W/SPECIAL NOS. ONLY/ |
| . |
W52 |
SKF SINGLE CAP BEARINGS WITH MARKING ON SIDE OPPOSITE CAP |
| . |
W521 |
SKF COMBINATION OF W5 PLUS W74 |
| . |
W522 |
SKF COMBINATION OF W81 PLUS W33/USED W/SPECIAL NOS. ONLY/ |
| . |
W523 |
SKF COMBINAT, ION OF W31 PLUS W76 |
| . |
W524 |
SKF COMBINATION C02 W507 |
| . |
W525 |
.SKF COMBINATION W31 W77 |
| . |
W526 |
SKF COMBINATION W506 W515 |
| . |
W527 |
SKF COMBINATION W22 W33 W26 |
| . |
W53 |
SKF BALL BEARINGS MODIFIED AND FLUSH GROUND ON ONE FACE ONLY |
| . |
W54 |
SKF SPECIAL QUIET RUNNING BEARINGS |
| . |
W55 |
SKF BEARINGS WITH LOCATING HOLES IN THE OUTER RING |
| . |
W56 |
SKF LIFTING HOLES IN FACE OF BEARINGS RING |
| . |
W57 |
SKF GE MOTOR BEARING QUALITY ASSURANCE |
| . |
W58 |
SKF OUTER RING MARKED TO SHOW HIGH POINT |
| . |
W59 |
SKF SPECIAL FORD MOTOR CO. QUALITY REQUIREMENTS |
| . |
W6 |
SKF GEAR SIDE MARKED ON BEARING |
| . |
W60 |
SKF QUALITY ASSURANCE U.S. NAVY PURCHASE OF G.E. BEARINGS |
| . |
W61 |
SKF BEARINGS W/3 TAPPED HOLES IN THE FACE OF THE OUTER RING |
| . |
W62 |
SKF CYL BEARING-SIDE FLANGES W/15-TO-30 MINUTES RELIEF ANGLE |
| . |
W63 |
SKF MARKING FOR DEVIATION FROM NOMINAL OUTER-DIAMETER SIZE |
| . |
W66 |
SKF BLIND HOLE IN O.D. OF CYLINDRICAL ROLLER BEARINGS |
| . |
W67 |
SKF CYLINDRICAL BEARINGS W/OVERSIZE O.D. FOR GREATER HOUSING FIT |
| . |
W7 |
SKF BEARING BORE DIAMETER INDICATED |
| . |
W70 |
SKF CYLINDRICAL W/INCREASED OUTER RING AXIAL CLEARANCE |
| . |
W71 |
SKF SPECIAL MARKING FOR SIKORSKY BEARINGS PURCHASED BY U.S. NAVY |
| . |
W72 |
SKF CYLINDRICAL BEARING W/ANGLED FLANGE INCREASED AXIAL CLARANCE |
| . |
W73 |
SKF SPHERICAL ROLLER BEARING WITH ONE COUNTERBORED HOLE IN OUTER RING |
| . |
W74 |
SKF BALL BEARING, J-CAGE TYPE WITH CONTROLLED CAGE DROP |
| . |
W75 |
SKF STD CONRAD BALL BEARING W/REPUBLIC ROCKED TUBE HOFORS BALLS |
| . |
W76 |
SKF FOUR TAPED HOLES IN EACH FACE OF OUTER RING |
| . |
W77 |
SKF SPHERICAL ROLLER BEARING WITH W33 GROOVE HOLES/HOLES CIBORED PLUGGED/ |
| . |
W79 |
SKF W33 SPHERICAL ROLLER WITH ONE HOLE COUNTERBORED |
| . |
W8 |
SKF NO LUBE-HOLE IN O.K. OF BEARING USED IN SY PILLOW BLOCK |
| . |
W80 |
SKF SPECIAL BEARING-I .R. , O.K. ROLLERS AIR-MELT CARBURIZED GRADE STEEL |
| . |
W81 |
SKF SPECIAL BEARING/I. R. AIR-MELT CARBURIZED GRADE OF STEEL |
| . |
W82 |
SKF SPECIAL BEARING/0. R. AIR-MELT CARBURIZED GRADE OF STEEL |
| . |
W83 |
SKF W81 PLUS W82, PLUS STANDARD THRU HARDENED ROLLERS |
| . |
W86 |
SKF SPECIAL BEARING/I. R. O.R. STD THRU HARD, ROLLERS CARBURIZED GRADE STEEL |
| . |
W90 |
SKF . SAME AS W80 , EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . |
W91 |
SKF SAME AS W81, EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . |
W92 |
SKF SAME AS W82 , EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . |
W93 |
SKF SAME AS VJ83, EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . |
W96 |
SKF SAME AS W86 , EX CARBURIZED GRADE STEEL CONSUMABLE VAC-MELTED |
| . |
WA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 1900 MG/MM |
| . |
WA |
TYSON SLOTTED CONE-SINGLE ANGULAR SLOT IN BACKFACE |
| . |
WB |
TYSON TWO SLOTS DIAMETRICALLY OPPOSITE IN BACK-FACE OF CONE |
| . |
WD |
TYSON SPECIAL SLOTTED CONE |
| . |
WE |
TYSON SLOTTED CONE- FULL LENGTH SLOT THROUGH BORE |
| . |
WHO |
REED DENTAL DRILL QUALITY BEARING |
| . |
WILL |
REED BEARING STABILIZED FOR 900-F OPERATION |
| . |
WLL |
SKF BEARING WITH PARCO-LUBRIZED SURFACES |
| . |
WM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 1900 MG/MM |
| . |
WP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 1900 MG/MM |
| . |
X |
SKF BOUNDARY DIMENSIONS CHANGED TO CONFORM TO INTERNAT STD |
| . |
X |
TYSON CONE, WITH KEYWAY |
| . |
X |
TYSON VARIATION FROM BASIC CUP |
| . |
XA |
TYSON CONE SPACER |
| . |
XB |
TYSON CONE SPACER |
| . |
XC |
TYSON CONE SPACER |
| . |
XD |
TYSON DOUBLE CONE OR CUP |
| . |
XL |
TYSON CONE, CUP OR ASSEMBLY SEALED WITH TY-SEAL |
| . |
Y |
SKF PRESSED BRASS OR BRONZE CAGE/EX 6303-Y |
| . |
YA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 2000 MG/IRTM |
| . |
YC |
SKF PRESSED BRASS OR BRONZE CAGE CENTERED ON INNER RACE |
| . |
YP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 2000 MG/MM |
| . |
Z |
REED ONE STAINLESS STEEL REMOVABLE SHIELD |
| . |
Z |
SKF SHIELD ON ONE SIDE/EX 6203-Z/ |
| . |
ZA |
REED TORQUE TEST, AVERAGE TORQUE VALUE OF 2100 MG/MM |
| . |
ZM |
REED TORQUE TEST, MODAL TORQUE VALUE OF 2100 MG/MM |
| . |
ZNBR |
SKF SHIELD SNAP RING ON SAME SIDE/EX 6206-ZNBR/ |
| . |
ZNR |
SKF SHIELD SNAP RING ON OPPOSITE SIDES/EX 6206-ZNR |
| . |
ZP |
REED TORQUE TEST, PEAK TORQUE VALUE OF 2100 MG/MRA |
| A |
. |
REED DEEP GROOVE NARROW SERIES STRAIGHT O.D., FLUSH RINGS |
| AHA |
. |
SKF REMOVAL SLEEVE WITH AMERICAN STD THREAD/PHILA |
| AN |
. |
SKF NUT FOR ADAPTER SLEEVE/PHILA |
| ARM |
. |
SKF REMOVAL NUT FOR ASK-TYPE SLEEVE/EX ARN-18 |
| ASK |
. |
SKF REMOVAL SLEEVE/EX ASK-15 |
| B |
. |
BREMEN LOOSE NEEDLE ROLLER W/SPHERICAL ENDS/STANDARD/EX B142 |
| B |
. |
REED BEARING MATERIAL-BERYLLIUM COPPER ALLOY |
| B |
. |
REED DEEP GROOVE, NARROW SERIES, STRAIGHT O.D., EXTENDED INNER RING |
| BB |
. |
BREMEN DRAWN CUP, OPEN END NEEDLE ROLL BRG/EX BB182212 |
| BB |
OH |
BREMEN SAME AS BB-, EXC WITH OIL-HOLE/EX BB- 182212-OH |
| BBH |
. |
BREMEN SAME AS BB- , EXC HEAVY-DUTY/EX BBH-162112 |
| BBH |
OH |
BREMEN SAME ASJ3BH-, EXC WITH OIL-HOLE/EX BBH-162112-OH |
| BD |
. |
BREMEN DRAWN CUP, CLOSED END, GREASE RETAINED NEEDLE ROLLER BRG |
| BDH |
. |
BREMEN DRAWN CUP, CLOSED END NEEDLE ROLL BRG/EX BDH-162116 |
| BDH |
OH |
BREMEN SAME AS BDH- , EXC WITH OIL-HOLE/EX BDH-162112-OH/ |
| BF |
. |
BREMEN DRAWN CUP W/OUTWARD TURNED LIP, GREASE RETAINED NEEDLE |
| BFF |
F |
SKF SPECIAL PILLOW BLOCK FOR BUFFALO FORGE- REPLACES BF-F |
| BN |
. |
BREMEN DRAWN CUP, RETAINER TYPE, CLOSED END ROLL BRG/BN-121608 |
| BNH |
. |
BREMEN SAME AS BN-, EXC HEAVY-DUTY/EX BNH-071108 |
| BP |
. |
BREMEN CAGE NEEDLE ROLLER ASSEMBLY/EX BP7767 |
| BR |
. |
BREMEN DRAWN CUP, RETAINER TYPE, OPEN END ROLLER BRG/BR-121608 |
| BR |
T |
BREMEN SAME AS BR- , EXC W/MOLDED NITRILE SEAL ON ONE SIDE |
| BR |
TT |
BREMEN SAME AS BR- , EXC W/MOLDED NITRILE SEAL ON BOTH SIDE |
| BRH |
. |
BREMEN SAME AS BR- , EXC HEAVY-DUTY/EX BRH-071108 |
| BT |
. |
BREMEN NEEDLE ROLLER THRUST BEARIN'G/EX BT-9929-5-46 |
| C |
. |
REED DEEP GROVE, NARROW SERIES, FLANGED O.D., FLUSH RINGS |
| CR |
. |
TYSON RIBBED CUP |
| D |
. |
REED DEEP GROOVE, NARROW SERIES, FLANGED O.D. , EXTENDED INNER RING |
| E |
. |
REED DEEP GROVE, MEDIUM SERIES, STRAIGHT O.D., FLUSH RINGS |
| ECB |
. |
SKF SPHERICAL BEARING/AIRMELT CARBURIZED STEEL I.R. ONLY/PHILA |
| ECC |
. |
SKF SPHERICAL BEARING AIRMELT CARBURIZED STEEL I.R. O.R. ONLY/ PHILA |
| ECD |
. |
SKF SPHERICAL BEARING, AIRMELT CARBURIZED STEEL, COMPLETE/PHILA |
| EDHP |
G |
SKF SYHP IN DUCTILE IRON, RE-LUBE, WITH 478-VSB SERIES BEARING |
| EE |
. |
SKF EXTRA-SMALL, INCH DIMENSION BALL BEARING/EX EE-9 |
| EE |
. |
TYSON LARGE BORE DOUBLE RIB TYPE CONSTRUCTION CONE |
| EEA |
. |
SKF SAME AS EE-, EXC REVISED DIMENSIONS/EX EEA2 , EEA2-2Z |
| EEB |
. |
SKF SAME AS EE-, EXC LARGER WIDTH TO ACCOMODATE SEALING |
| EGA |
. |
SKF SPHERICAL BEARING/AIRMELT CARBURIZED STEEL, O.R. ONLY/PHILA |
| EH |
. |
TYSON EXTRA HEAVY SERIES CONE OR CUP |
| EL |
. |
TYSON EXTRA LIGHT SERIES CONE OR CUP |
| EP |
. |
SKF SPHERICAL ROLLER BEARING W/PRECISION TOLERANCES/PHILA/ |
| EPCA |
. |
SKF SAME AS ECA-, EXCEPT WITH PRECISION TOLERANCES |
| EPCB |
. |
SKF SAME AS ECB-, EXCEPT WITH PRECISION TOLERANCES |
| EPCC |
. |
SKF SAME AS ECC-, EXCEPT WITH PRECISION TOLERANCES |
| EPCD |
. |
SKF SAME AS ECD-, EXCEPT WITH PRECISION TOLERANCES |
| EPVA |
. |
SKF SAME AS EVA-, EXCEPT WITH PRECISION TOLERANCES |
| EPVB |
. |
SKF SAME AS EVB- , EXCEPT WITH PRECISION TOLERANCES |
| EPVC |
. |
SKF SAME AS EVC-, EXCEPT WITH PRECISION TOLERANCES |
| EPVD |
. |
SKF SAME AS EVD-, EXCEPT WITH PRECISION TOLERANCES |
| ER |
. |
SKF TRIPLE SEAL RING FOR PILLOW BLOCK/EX ER-846 |
| EVA |
. |
SKF SPHERICAL BEARING, VACUUM MELT CARBURIZED STEEL, O.R. ONLY/ PHILA |
| EVB |
. |
SKF SPHERICAL BEARING, VACUUM MELT CARBURIZED STEEL, I.R. ONLY/ PHILA |
| EVC |
. |
SKF SPHERICAL BEARING, VACUUM MELT CARBURIZED STEEL, I.R. O.R. ONLY/PHILA |
| EVD |
. |
SKF SPHERICAL BEARING, VACUUM MELT CARBURIZED STEEL, COMPLETE/ PHILA |
| F |
. |
REED DEEP GROOVE, MEDIUM SERIES, CYLINDRICAL O.D., EXTENDED INNER RING |
| F |
. |
SKF PRESSED STEEL FLANGE, 3-BOLTS/EX F-40 |
| FD |
. |
SKF FY IN DUCTILE IRON, NON-RELUBE, WITH 479 SERIES BEARING |
| FD |
C |
SKF FALSE TWIST SPINDLE, INTERNAL DES CHANGED/EX FD-630-C |
| FD |
G |
SKF FY IN DUCTILE IRON, RE-LUBE, WITH 479 SERIES BEARING |
| FD |
P |
SKF FY IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 479 SERIES BEARING |
| FD |
PG |
SKF FY IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 479 SERIES BEARING |
| FDL |
. |
SKF FYL IN DUCTILE IRON, NON-RELUBE, WITH 454 SERIES BEARING |
| FDL |
G |
SKF FYL IN DUCTILE IRON, RE-LUBE, WITH 454-VSB SERIES BEARING |
| FDL |
P |
SKF FYL IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 454 SERIES BEARING |
| FDL |
PG |
SKF FYL IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 454-VSB SERIES BEARING |
| FDP |
. |
SKF FYP IN DUCTILE IRON, NON-RELUBE, WITH 478 SERIES BEARING |
| FDP |
G |
SKF FYP IN DUCTILE IRON, RE-LUBE, WITH 478-VSB SERIES BEARING |
| FDP |
P |
SKF FYP IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 478 SERIES BEARING |
| FDP |
PG |
SKF FYP IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 478-VSB SERIES BEARING |
| FDT |
. |
SKF FYT IN DUCTILE IRON, NON-RELUBE, WITH 479 SERIES BEARING |
| FDT |
G |
SKF FYT IN DUCTILE IRON, RE-LUBE, WITH 479 SERIES BEARING |
| FDT |
P |
SKF FYT IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 479 SERIES BEARING |
| FDT |
PG |
SKF FYT IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, -479 SERIES BEARING |
| FDTL |
. |
SKF FYTL IN DUCTILE IRON, NON-RELUBE, WITH 454 SERIES BEARING |
| FDTL |
G |
SKF FYTL IN DUCTILE IRON, RE-LUBE, WITH 454-VSB SERIES BEARING |
| FDTL |
P |
SKF FYTL IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 454 SERIES BEARING |
| FDTL |
PG |
SKF FYTL IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 454- VSB SERIES BEARING |
| FDTP |
. |
SKF FYTP IN DUCTILE IRON, NON-RELUBE, WITH 478 SERIES BEARING |
| FDTP |
G |
SKF FYTP IN DUCTILE IRON, RE-LUBE, WITH 478- VSB SERIES BEARING |
| FDTP |
P |
SKF FYTP IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 478 SERIES BEARING |
| FDTP |
PG |
SKF FYTP IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 478- VSB SERIES BEARING |
| FDTX |
. |
SKF FYTX IN DUCTILE IRON, NON-RELUBE, WITH 477 SERIES BEARING |
| FDTX |
G |
SKF FYTX IN DUCTILE IRON, RE-LUBE, WITH 477 SERIES BEARING |
| FDTX |
P |
SKF FYTX IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 477 SERIES BEARING |
| FDTX |
PG |
SKF FYTX IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 477 SERIES BEARING |
| FDX |
. |
SKF FYX IN DUCTILE IRON, NON-RELUBE, WITH 477 SERIES BEARING |
| FDX |
G |
SKF FYX IN DUCTILE IRON, RE-LUBE, WITH 477 SERIES BEARING |
| FDX |
P |
SKF FYX IN DUCTILE IRON, REV. MOUNTED, NON-RELUBE, 477 SERIES BEARING |
| FDX |
PG |
SKF FYX IN DUCTILE IRON, REV. MOUNTED, RE-LUBE, 477 SERIES BEARING |
| FE |
. |
SKF BOLSTER SPRINGS/EX FE-148/ TEXTILE APPLICATION |
| FL |
. |
SKF SAME AS FP , EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| FP |
. |
SKF 3-BOLT PRESSED STEEL ROUND FLANGE BEARING/EX FP-102 |
| FP |
. |
SKF FIXED BOSS TOP ROLLER/EX FP-2/TEXTILE APPLICATION |
| FR |
. |
SKF BELT GUIDE ROLLER/EX FR-23241/TEXTILE APPLICATION |
| FT |
. |
SKF PRESSED STEEL FLANGE, 2-BOLTS/EX FT-40/ |
| FTL |
. |
SKF SAME AS FTP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| FTP |
. |
SKF 2-BOLT PRESSED STEEL ELONGATED FLANGE BEARING/EX FTP102 |
| FY |
. |
SKF FLANGED HOUSING BEARING W/SET SCREW COLLAR/EX FY-102 |
| FY |
X |
SKF FLANGED HOUSING BEARING W/ECCENTRIC COLLAR/EX FY-102-X |
| FYL |
. |
SKF SAME AS FYP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| FYP |
. |
SKF FLANGED HOUSING BEARING W/SET SCREW COLLAR/EX FYP-102 |
| FYR |
. |
SKF FLANGED ROUND HOUSING SPHERICAL BEARING W/SET SCREW/ EX FYR107 |
| FYR |
P |
SKF SAME AS FYR- , EXC REVERSE FLANGE MOUNTING/FYR-107-P |
| FYTL |
. |
SKF SAME AS FYTP EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| FYTP |
. |
SKF TWO BOLTS, CAST IRON FLANGE UNIT WITH 478 SERIES BEARING |
| G |
. |
REED DEEP GROOVE, MEDIUM SERIES, FLANGED O.D., FLUSH RINGS |
| GL |
. |
SKF SAME AS GP , EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| GN |
A |
SKF HI-CAPACITY N-SERIES W/HYATT CORNER RADIUS |
| GNF |
A |
SKF HI-CAPACITY NF-SERIES W/HYATT CORNER RADIUS |
| GNJ |
A |
SKF HI-CAPACITY NJ-SERIES W/HYATT CORNER RADIUS |
| GNP |
A |
SKF HI-CAPACITY NP-SERIES W/HYATT CORNER RADIUS |
| GNU |
A |
SKF HI-CAPACITY NU-SERIES W/HYATT CORNER RADIUS |
| GNUP |
A |
SKF HI-CAPACITY NUP-SERIES W/HYATT CORNER RADIUS |
| GP |
. |
SKF CYL CARTRIDGE W/SPHERED O.D. RUBBER MOUNTING/EX GP-12 |
| H |
. |
REED DEEP GROOVE, MEDIUM SERIES, FLANGED O.D., EXTENDED INNER RING |
| H |
. |
TYSON HEAVY SERIES CUP OR CONE |
| HA |
. |
SKF ADAPTER SLEEVE FOR AMERICAN STANDARD SHAFT/EX HA-2313 |
| HF |
. |
SKF BOLSTER INSERT/EX HF-4/TEXTILE APPLICATION |
| HH |
. |
TYSON HEAVY-HEAVY SERIES CUP OR CONE |
| HHC |
AB |
SKF SIZE OF SER HNC-A WITH WIDTH NON-CONFORMING ISO STDS |
| HHJ |
AB |
SKF SIZE OF SER HNJ-A WITH WIDTH NON-CONFORMING ISO STDS |
| HM |
. |
SKF BOLSTER INSERT/EX HM-337/OLD STYLE, REPLACEMENT ONLY |
| HM |
. |
TYSON HEAVY-MEDIUM SERIES CUP OR CONE |
| HMJ |
A |
SKF CRB, TWO SNAP-RINGS IN O.R., ONE LIP IN I.R., J-CAGE/HNJ206-A |
| HMVP |
. |
SKF HYDRAULIC NUT/EX HMVP-76 |
| HNC |
A |
SKF CRB, TWO SNAP-RINGS IN O.K., TWO LIPS IN I.R., J-CAGE/HNC206A |
| HNC |
ABV |
SKF SIZE OF SER HNC-AV WITH WIDTH NON-CONFORMING ISO STDS |
| HNC |
AV |
SKF CRB, TWO SNAP-RINGS IN O.K., TWO LIPS IN I.R., NO CAGE |
| HNU |
. |
SKF OUTER RING OF SNAP-RING TYPE CYLINDRICAL ROLLER BEARINGS |
| HNU |
A |
SKF CYLINDRICAL ROLLER BEARINGS TWO SNAP-RINGS IN O.R., STRAIGHT I.R. , J-CAGE/HNU-206-A |
| HUU |
J |
SKF CAGE OF SNAP-RING TYPE CYLINDRICAL ROLLER BEARINGS |
| HZ |
. |
SKF BOLSTER BASE UNIT/EX HZ-66/TEXTILE APPLICATION |
| I- |
. |
SKF AS PER DRAWING I-.../SER OR SPEC/STAMPED CHANGES TO |
| J |
. |
BREMEN LOOSE NEEDLE ROLLER W/FLAT SHEARED ENDS/EX J-1056 |
| J |
. |
REED DEEP GROOVE, EXTRA NARROW SERIES, STRAIGHT O.D., FLUSH RINGS |
| J |
. |
TYSON SIZE EQUIVALENT TO CORRESPONDING IN TIMKEN J-LINE |
| K |
. |
TYSON SPECIAL HEAVY DOUBLE CUP OR ROLLER ASSEMBLY |
| KNU |
AB |
SKF SIZE OF SER HNU-A WITH WIDTH NON-CONFORMING ISO STDS |
| L |
. |
TYSON LIGHT SERIES CUP OR CONE |
| LER |
. |
SKF TRIPLE SEAL RING FOR PILLOW BLOCK/EX LER-14 |
| LHNC |
AB |
SKF SAME AS LHNC-A WITH WIDTH NON-CONFORMING TO ISO STDS |
| LHNJ |
A |
SKF INNER RACE OF HNJ-A/EX LHNJ-206-A |
| LHNJ |
AB |
SKF SAME AS LHNJ-A WITH WIDTH NON-CONFORMING TO ISO STDS |
| LHNU |
A |
SKF INNER RACE OF HNU-A/EX LHNU-206-A |
| LHNU |
AB |
SKF SAME AS LHNU-A WITH WIDTH NON-CONFORMING TO ISO STDS |
| LL |
. |
TYSON LIGHT-LIGHT SERIES CONE OR CUP |
| LM |
. |
TYSON LIGHT-MEDIUM SERIES CUP OR CONE |
| LP |
. |
SKF LOOSE BOSS TOP ROLL/EX LP-512-32/TEXTILE APPLICATION |
| LZ |
. |
SKF CAPPED-BAR TYPE TOP ROLLER/EX LZ-512/TEXTILE APPLICATION |
| M |
. |
BREMEN SAME AS B-PREFIX BUT DIFFER HEAT-TREAT O.R. DIMENS DATA |
| M |
. |
REED ANGULAR CONTACT, NARROW SERIES, FLANGED O.D., FLUSH RINGS |
| M |
. |
TYSON MEDIUM SERIES CUP OR CONE |
| MB |
. |
SKF LOCKWASHER/EX MB-18 |
| MBL |
. |
SKF LOCKWASHER/EX MBL-36 |
| N |
. |
REED DEEP GROOVE, INCH SERIES, STRAIGHT O.D. FLUSH RINGS |
| N |
. |
SKF CYLINDRICAL BEARING W/TWO FLANGES IN I.R. NO FLANGES IN O.R. |
| N |
. |
SKF LOCKNUT/EX N-08/PHILA ONLY |
| NA |
. |
TYSON NON-ADJUSTABLE CONE/ FACTORY ADJUST/USED W/DOUBLE CUP |
| NF |
. |
SKF CYLINDRICAL BEARING W/TWO FLANGES IN I.R. ONE FLANGE IN O.R. |
| NH |
. |
SKF SAME AS N.J.., PLUS STABILIZING RING |
| NJ |
. |
SKF CYLINDRICAL BEARING W/ONE FLANGE IN I.R. TWO FLANGES IN O.R. |
| NN |
. |
SKF 2-OR MORE-ROW CYLINDRICAL BEARING/FLANGED INNER, FLANGLESS OUTER |
| NN |
K |
SKF SAME AS NN-, EXC L-TO-12 TAPER BORE/EX NN-3007-K/ |
| NP |
. |
SKF CYL BRG, 2-FLANGE INNER, 1-FLANGE OUTER W/PLATE |
| NU |
. |
SKF CYLINDRICAL BEARING W/NO FLANGES IN I.R. TWO FLANGE IN O.R. |
| NUP |
. |
SKF CYLINDRICAL BEARING, 2-FLANGE OUTER, 1-FLANGE INNER W/PLATE |
| P |
. |
REED DEEP GROOVE, INCH SERIES, FLANGED O.D., FLUSH RINGS |
| P |
. |
SKF LOCK-PLATE FOR LOCKNUT/EX P-76/ |
| P |
. |
SKF SPHERICAL ROLLER BEARING W/SPLIT O.R. /EX 22320-P/ |
| PK |
. |
SKF PENDULUM WEIGHTING ARM/EX PK-101/TEXTILE APPLICATION |
| R |
. |
REED DEEP GROOVE, INCH SERIES, STRAIGHT O.D., EXTENDED INNER RING |
| R |
. |
SKF SMALL SIZE SINGLE ROW, DEEP-GROOVE BALL BEARING/EX R-9 |
| RGNU-F |
. |
SKF OUTER RING CAGE ROLLER ASSEMBLY STAVE TYPE G SERIES BEARINGS |
| RHNU |
BJ |
SKF SAME AS RHNU-J WITH WITH NON-CONFORMING TO ISO STDS |
| RHNU |
J |
SKF OUTER RING ROLLER ASSY OF HNJ-A AND HNU-A/RHNU206-J |
| RL |
. |
SKF SAME AS RP , EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| RN |
. |
SKF CYLINDRICAL ROLLER BEARING, 2-FLANGE INNER, NO OUTER RING/ EX RM-210/ |
| RN |
. |
SKF REMOVAL NUT FOR SK-SLEEVE/EX RN-12 |
| RNU |
. |
SKF CYLINDRICAL ROLLER BEARING, 2-FLANGE OUTER, NO INNER RING/ EX RNU-210 |
| RP |
. |
SKF RUBBER MOUNTED CYLINDRICAL CARTRIDGE UNIT/EX RP-14 |
| S |
. |
SKF ADAPTER SLEEVE/EX S-15, PART OF SNW -15 |
| SA |
. |
REED SAME AS A-PREFX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SAF |
. |
SKF SPLIT PILLOW BLOCK HOUSING W/TRIPLE SEALS/EX SAF-609 |
| SAFS |
. |
SKF SAF PILLOW BLOCK OF CAST STEEL |
| SB |
. |
REED SAME AS B-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SC |
. |
REED SAME AS C-PREFIX, EXC 400-C S/STEEL IN LIEU OF STD 52100 |
| SD |
. |
REED SAME AS D-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SD |
. |
SKF SY IN DUCTILE IRON, NON-RELUBE, WITH 479 SERIES BEARING |
| SD |
G |
SKF SY IN DUCTILE IRON, RE-LUBE, WITH 479 SERIES BEARING |
| SDAF |
. |
SKF SPLIT PILLOW BLOCK HOUSING W/TRIPLE SEALS/EX SDAF-530 |
| SDAFS |
. |
SKF SDAF PILLOW BLOCK OF CAST STEEL |
| SDH |
. |
SKF SYH IN DUCTILE IRON, NON-RELUBE, WITH 479 SERIES BEARING |
| SDH |
G |
SKF SYH IN DUCTILE IRON, RE-LUBE, WITH 479 SERIES BEARING |
| SDHL |
. |
SKF SYHL IN DUCTILE IRON, NON-RELUBE, WITH 454 SERIES BEARING |
| SDHL |
G |
SKF SYHL IN DUCTILE IRON, RE-LUBE, WITH 454-VSB SERIES BEARING |
| SDHP |
. |
SKF SYHP IN DUCTILE IRON, NON-RELUBE, WITH 478 SERIES BEARING |
| SDHX |
. |
SKF SYHX IN DUCTILE IRON, NON-RELUBE, WITH 477 SERIES BEARING |
| SDHX |
G |
SKF SYHX IN DUCTILE IRON, RE-LUBE, WITH 477 SERIES BEARING |
| SDK |
. |
SKF SYX IN DUCTILE IRON, NON-RELUBE, WITH 477 SERIES BEARING |
| SDK |
G |
SKF SYX IN DUCTILE IRON, RE-LUBE, WITH 477 SERIES BEARING |
| SDL |
. |
SKF SYL IN DUCTILE IRON, NON-RELUBE, WITH 454 SERIES BEARING |
| SDL |
G |
SKF SYL IN DUCTILE IRON, RE-LUBE WITH 454-VSB SERIES BEARING |
| SDP |
. |
SKF SYP IN DUCTILE IRON, NON-RELUBE, WITH 478 SERIES BEARING |
| SDP |
G |
SKF SYP IN DUCTILE IRON, RE-LUBE, WITH 478-VSB SERIES BEARING |
| SE |
. |
REED SAME AS E-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SF |
. |
REED SAME AS F-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SG |
. |
REED SAME AS G-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SJ |
. |
REED SAME AS J-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD. 52100 |
| SK |
. |
SKF REMOVABLE SLEEVE/EX SK-28 |
| SL |
. |
SKF SAME AS SP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| SN |
. |
REED SAME AS N-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SNP |
. |
SKF ADAPTER WITH NUT AND LOCKPLATE/EX SNP-3098 |
| SNW |
. |
SKF ADAPTER WITH NUT AND LOCKWASHER/EX SNW-08 |
| SP |
. |
REED SAME AS P-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SP |
. |
SKF PRESSED STEEL PILLOW BLOCK/EX SP-102 |
| SR |
. |
BREMEN LOOSE NEEDLE ROLLER W/FLAT GROUND ENDS/EX SR-902/ |
| SR |
. |
REED SAME AS R-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| SR |
. |
SKF SR-23, -24, -25 ARE IDLER PULLEY SPINDLES/TEXTILE APPLICATION/ |
| SR |
. |
SKF SR-270, -290, -3120 ARE COMPLETE TENSION PULLEYS/TEXTILE APPLICATION/ |
| SR |
. |
SKF STABILIZING RING FOR PILLOW BLOCK/EX SR-20-17, SR-1610 |
| SR |
. |
SKF TAPE TENSION PULLEY/EX SR-23/TEXTILE APPLICATION |
| SR |
B |
SKF SAME AS SR- , EXCEPT PARKERIZED SHELL/EX SR-7-B |
| SR |
B |
SKF SAME AS SR- , EXCEPT SPECIAL DIMENSIONS/EX SR-23-B |
| SR |
E |
SKF SAME AS SR-, EXC INTERNAL F LINGER PARKERIZED SHELL |
| SR |
H |
SKF SAME AS SR-, EXCEPT EXTRA WIDTH/EX SR-290-H |
| SRL |
. |
SKF SAME AS SRP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| SRP |
. |
SKF PRESSED STEEL PILLOW BLOCK, RUBBER MOUNTED/EX SPR-14 |
| SS |
. |
REED SAME AS S-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
| ST |
. |
SKF LINEAR MOTION ASSEMBLY, HELD TYPE/EX ST-1232 |
| SW |
. |
SKF LINEAR 'MOTION ASSY, FLOATING TYPE/EX SW-1232 |
| SY |
. |
SKF UNIT BALL BEARING PILLOW BLOCK, SET SCREW COLLAR/EX SY-100 |
| SYH |
X |
SKF SAME AS SY, EXC ECCENTRIC COLLAR HEIGHT/EX SYH- 104-X |
| SYHL |
. |
SKF SAME AS SYHP EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| SYHP |
. |
SKF SAME AS SYH, EXCEPT WITH 478 BEARING SERIES/EX SYHP-102 |
| SYL |
. |
SKF SAME AS SYP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| SYP |
. |
SKF SAME AS SY , EXC 478 SER BEARING ECCENTRIC COLLAR/SYP102 |
| SYR |
. |
SKF SPHERICAL ROLLER BEARING PILLOW BLOCK UNIT/EX SYR-208 |
| TB |
. |
SKF BALL BEARING TAKE-UP UNIT/EX TB-104 |
| TBL |
. |
SKF SAME AS TBP, EXC WITH 454 AGRICULTURAL SEAL BEARING SERIES |
| TBP |
. |
SKF BALL BEARING TAKE-UP UNIT/EX TBP-104 |
| TBX |
. |
SKF BALL BEARING TAKE-UP UNIT/EX TBX-104 |
| TM |
. |
REED TORQUE TEST, MODAL TORQUE VALUE OF 2000 MG/IMN |
| TW |
. |
BREMEN NEEDLE ROLLER THRUST RACE/EX TW-1220-2 |
| TY |
R |
SKF TAKE-UP UNIT WITHOUT ADJUSTING FRAINE/EX TY-203-R |
| TY |
R-PS |
SKF TAKE-UP UNIT WITH ADJUSTING FRAME/EX TY-203-R-PS-12 |
| UL |
. |
SKF BOTTOM ROLLER BEARING/EX UL-LL-28/TEXTILE APPLICATION |
| VR |
. |
SKF SEPARATOR ROLLS/EX VR-2/TEXTILE APPLICATION |
| W |
. |
SKF GREASE SEAL/EX W-2854 |
| W |
. |
SKF GREASE LOCK WASHER/EX W-08 |
| X |
. |
TYSON EXPERIMENTAL OR LIMITED PRODUCTION/EX X-68-1/ |
| Y |
A |
SKF PROPELLER SHAFT BOX/EX Y-5463-A |
| •SH |
. |
REED SAME AS H-PREFIX, EXC 440-C S/STEEL IN LIEU OF STD 52100 |
Bearing >Bearing Numbers > SKF bearings